一、 网络环境 1、主机A：安装freebsd4.7，安装三块网卡fXP0、xl0和xl1。 fxp0为对外网卡，IP：x.x.x.x ISP为我提供的IP地址 xl0为对内公共区域网卡，IP：192.168.0.1 xl1为对内服务提供区域网卡，IP：192.168.80.1 2、主机B：对外提供www服务主机，ip地址为：192.168.80.80 3、主机C：对外提供FTP服务主机，ip：192.168.80.3。 4、其他工作站N台。
二、编译内核 1、#cd /sys/i386/conf #cp GENERIC kernel_IPF 2、编译kernel_IPF,加入一下选项： options IPFILTER options IPFILTER_LOG options IPFILTER_DEFAULT_BLOCK 3、#/usr/sbin/config kernel_IPF #cd ../../compile/kernel_IPF #make kepend #make #make install 4、编辑/etc/rc.rc.conf,打开以下选项： defaultrouter="x.x.x.1" x.x.x.1为ISP提供的网关 gateway_enable="YES" ipfilter_enable＝"YES" ipnat_enable="YES" 5、重新启动系统：reboot
三、配置防火墙 1、 设置地址转换ipnat。在/etc下新建文件ipnat.rules,内容为： map fxp0 192.168.0.0/16 -> 0/32 proxy port ftp ftp/tcp map fxp0 192.168.0.0/24 -> 0/32 portmap tcp/udp 10000:30000 map fxp0 192.168.0.0/24 -> 0/32 map fxp0 192.168.80.0/24 -> 0/32 portmap tcp/udp 300001:60000 map fxp0 192.168.80.0/24 -> 0/32 portmap rdr fxp0 x.x.x.x/32 port 80 -> 192.168.0.2 port 80 rdr fxp0 x.x.x.x/32 port ftp -> 192.168.0.3 port ftp rdr fxp0 x.x.x.x/32 port 30001-50000 -> 192.168.80.3 port 30001 tcp 2、设置包过滤ipfilter。在/etc下新建文件ipf.rules,内容为： block in log quick all with short block in log quick all with ipopts block in log quick all with frag block in log quick all with opt lsrr block in log quick all with opt ssrr 以上五句为过滤掉可能会带来安全问题的短数据包或具备路由信息的数据包以及防止非法扫描服务器 pass out on xl0 all pass in on xlo all pass out on xl1 all pass in on xl1 all pass out quick on lo0 all pass in quick on lo0 all 以上为内部网络界面和loopback网络界面可以自由发送和接受数据包 block out on fxp0 all 以上为屏蔽外部网络界面向外发送数据包 block out log on fxp0 from any to 192.168.0.0/16 block out log quick on fxp0 from any to 0.0.0.0/8 block out log quick on fxp0 from any to 169.254.0.0/8 block out log quick on fxp0 from any to 10.0.0.0/8 block out log quick on fxp0 from any to 127.16.0.0/12 block out log quick on fxp0 from any to 127.0.0.0/8 block out log quick on fxp0 from any to 192.0.2.0/24 block out log quick on fxp0 from any to 204.152.64.0/23 block out log quick on fxp0 from any to 224.0.0.0/3 以上为屏蔽不合法地址的输出数据 pass out log on fxp0 proto tcp/udp from any to any keep state pass out log on fxp0 proto icmp all keep state 以上为允许TCP 、UDP、ICMP数据包向外发送出去，并且允许回应数据包发送回到内部网络 block in log on fxp0 from 192.168.0.0/16 to any block in log quick on fxp0 from 10.0.0.0/8 to any block in log quick on fxp0 from 172.16.0.0/12 to any block in log quick on fxp0 from 127.0.0.0/8 to any block in log quick on fxp0 from 192.0.2.0/24 to any block in log quick on fxp0 from 169.254.0.0/16 to any block in log quick on fxp0 from 224.0.0.0/3 to any block in log quick on fxp0 from 204.152.64.0/23 to any block in log quick on fxp0 from x.x.x.x/32 to any block in log quick on fxp0 from any to x.x.x.0/32 block in log quick on fxp0 from any to x.x.x.255/32 以上为屏蔽具备内部网络地址的数据包被转发到外部网络 pass in quick on fxp0 proto tcp from any to any port = 80 flags S/SA keep state pass in quick on fxp0 proto tcp from any to any port = ftp flags S/SA keep state pass in quick on fxp0 proto tcp from any to any port = ftp-data flags S/SA keep state pass in quick on fxp0 proto tcp from any to any port 30000 >< 50001 flags S/SA keep state 以上为允许www和ftp进入，并且允许对ftp数据端口的数据进行转发 block in quick on fxp0 all 禁止其他的连接进入fxp0 block in log quick on fxp0 proto icmp from any to any icmp-type redir block in log quick on fxp0 proto icmp from any to any block in log quick on fxp0 proto icmp from any to any icmp-type echo 以上为禁止别人ping我得网络 block return-rst in log on fxp0 proto tcp from any to any flags S/SA block return-icmp(net-unr) in log on fxp0 proto udp from any to any 以上对其他tcp请求，防火墙回应一个RST数据包关闭连接。对UDP请求，防火墙回应网络不可达到的ICMP包。 或者在/etc/sysctl.conf中加入： net.inet.tcp.blackhole=2 net.inet.udp.blackhole=1 能够有效地避免端口扫描 3、然后编辑/etc/rc.conf，加入一下命令，让ipfilter和ipnat在系统启动的时候可以自动加载： ipfilter_enables=”YES” ipf –C –f /etc/ipf.rules ipfilter_flags=”-E” ipnat_enable=”YES” ipnat_program=”/sbin/ipnat –CF -f” ipnat_rules=”/etc/ipnat.rules” ipmon_enable=”YES” ipmon_flags=”-D /var/log/ipfilter.log” 4、在/usr/log/建立文件ipfilter.log,并更改其属性为755，这样你的防火墙日志就记录到/var/log/ipfilter.log文件中，可以随时对其进行查看。
四、设置FTP服务器，使其支持被动连接（pasv） 1．Proftpd：编辑你的proftpd的配置文件proftpd.conf,加入一下内容： MasqueradeAddress x.x.x.x PassivePorts 30001 50000 2．Pure-ftpd:编辑你的FTP配置文件，加入一下内容： PassivePortRange 30001 50000 ForcePassiveIP x.x.x.x 3．Serv-U: a、在serv-U的”本地服务器”―――”设置”―――”高级”―――”PASV端口范围”输入30001 50000 b、在serv-U的”域”―――”你自己建立的域”―――”设置”―――”高级”选中”允许被动模式传送”，” 使用IP”输入：x.x.x.x
[1] [2] 下一页
（出处：http://www.sheup.com）
上一页 [1] [2]