当前位置:Linux教程 - Linux综合 - 使用netcat命令网络同步复制系统

使用netcat命令网络同步复制系统

·系统提示“找不到网络路径”怎么办?·XP系统网络优化六招简单技巧·最常用的网络命令精萃·深入掌握网络加密及解密方法·网络符号表情大全·制作一张含有网络功能的dos启动盘·虚拟网络计算工具VNC使用指南·必学:电脑与网络维护常用技巧·网络路由安全攻防对策分析及实践·常用网络命令及命令实例详解    本记录思想是通过以太网络,配合简单的3个命令,实现把配置好了的完整系统复制到其他机器。以便于局域网上的快速安装,并减少单台机器系统配置的过程。 使用了3个命令:nc,dump,restore。 代码: netcat 简称 nc. Netcat 是一把非常简单易用的基于 TCP/IP 协议(C/S模型的)的“瑞士军刀”(man里面,第一句就是这样说的),它能允许我们通过网络创建管道(pipe)。 dump 和 restore 是用于备份和恢复系统的常用命令。位于dump包中。可以apt-get install dump。 实验的目的:我们将源机器的根分区,通过 dump/restore 和 nc 来传送到目标机器的指定分区。 先实验将源机器的/var/cache/apt/archives/复制到目标机器。 1:在接收端(目标电脑),创建一个 netcat 的监听例程(-l),这个监听例程将管道输出到 restore。 把接受到的数据写到目标机器。 nc -l -p 2000 -q 1 restore -r -f - 这里-p是建立一个端口。-q 选项是让 nc 在到达文件结束(EOF)时延时n秒后,自动停止运行。 2:在 源电脑, 创建另一个 netcat 的例程,这个例程将它从管道里得到的输入(也就是dump备份的数据)发给目标电脑。 dump -0 -f - /dir nc <target-ip> 2000 这里 target-IP 是目标电脑的 IP 地址。 2000是端口号。 以下是man里面的原版说明,可以参考。 代码: restore说明:  -f file     Read  the  backup  from  file; file may be a special device file like /dev/st0 (a tape drive), /dev/sda1 (a disk drive), an ordinary file, or - (the standard input). If the name of the file isof the form host:file or user@host:file, restore reads from  the named file on the remote host using rmt(8).  -r     Restore (rebuild) a file system. The target file  system  should be made pristine with mke2fs(8), mounted, and the user cd’d into the pristine file system before starting the restoration of  the initial  level  0  backup. If the level 0 restores sUCcessfully, the -r flag may be used to  restore  any  necessary  incremental backups on top of the level 0. The -r flag precludes an interac‐tive file extraction and can be detrimental to one’s health (not to mention the disk) if not used carefully. An example:                      mke2fs /dev/sda1                      mount /dev/sda1 /mnt                      cd /mnt                      restore rf /dev/st0    Note  that  restore  leaves  a  file restoresymtable in the root Directory  to  pass  information  between  incremental   restore passes.   This  file should be removed when the last incremental has been restored. 代码: dump说明: -f file     Write the backup to file; file may be a special device file like /dev/st0 (a tape drive), /dev/rsd1c (a floppy  disk  drive),  an ordinary  file,  or - (the standard output). Multiple file names may be given as a single argument separated by commas. Each file will  be  used  for  one dump volume in the order listed; if the dump requires more volumes than the number of names  given,  the last file name will used for all remaining volumes after prompt‐ing for media changes. If the name of the file is  of  the  form host:file or user@host:file dump writes to the named file on the remote host (which should already exist, dump doesn’t  create  a new  remote  file)  using  rmt(8).  The default path name of the remote rmt(8) program is /etc/rmt; this can be overridden by the environment variable RMT. [-level#] 代码: nc - TCP/IP swiss army knife说明:        -l           listen mode, for inbound connects        -n           numeric-only IP addresses, no DNS        -o file      hex dump of traffic        -p port      local port number  (port  numbers  can  be  individual  or ranges: lo-hi [inclusive])        -q seconds   after  EOF  is detected, wait the specified number of seconds and then quit. ------------------------- 实验结果,数据送传可以,只是目标路径有些偏差。2边执行了 代码: sudo dump -0 -f - /var/cache/apt/archives/ nc 10.23.1.100 2000 ~$ nc -l -p 2000 -q 1 restore -r -f - 结果数据全部传送到了~/var/cache/apt/archives/。 当时考虑失误,安装目标机器系统时,图简单,安装时选了格式全盘,安装的server,然后安装了dump包。结果搞得没有空闲分区测试。直接根目录对根目录传送,提示失败,被中断。想来也想得到。挂载了并且在运行中的根目录怎么会让你覆盖哦。 总体来说,实验还是成功的。数据传送正常。以后就只要找个带了nc/dump/restore命令的live cd。就可以在裸机或者其他任何有空间的机器上,复制其他机器上配置好了的Linux系统了。我想以太网络的速度应该比usb硬盘之类的要好得多。 省去了独立安装系统时,系统检测,解包,下载包,配置软件的时间,这些也是占用很长的时间的。 忘记了,复制以后,需要按照机器设置,修改/etc/fstab(分区结构), /etc/network/interfaces(网络ip,dhcp的就可以不要修改), /boot/grub/menu.lst(多数不要修改,除开目标机器有其他不同的系统), 然后就是显卡和声卡(这个我以前写过),硬件的驱动。

(出处:http://www.sheup.com)